Air Purification Installation: Dispatched to resolve persistent odors and concerns about indoor air quality and airborne contaminants. Installed a UV light air purification system within the HVAC unit, mounted the lamp assembly securely, connected electrical power with safety shutoff, and tested operation to reduce bacteria, mold, and odors throughout the home.

Heat Pump Repair: Arrived on-site to inspect a heat pump experiencing ice buildup on the outdoor unit during cold conditions. Tested defrost controls and sensors, identifying a malfunctioning defrost control board. Replaced the board, verified proper defrost timing, and tested system operation to ensure reliable winter performance.

Heating System Repair: Dispatched to address uneven temperatures throughout the home. Inspected blower motor performance, ductwork, and airflow restrictions. Diagnosed a failing blower motor and debris buildup on the blower wheel. Replaced the motor, cleaned the wheel, and tested airflow and temperature distribution to restore even heating.

AC Repair: Arrived on-site to troubleshoot an air conditioning system that would not start. Verified incoming power, inspected electrical components, and identified a failed contactor and loose wiring connections. Replaced the contactor, secured all electrical connections, and tested system startup and cooling operation.

Furnace Replacement: Dispatched to evaluate a furnace experiencing repeated fault codes and safety shutdowns. Inspection revealed a failed secondary heat exchanger creating unsafe operating conditions. Removed the furnace, installed a new high-efficiency replacement, ensured proper venting and condensate drainage, and tested system startup and heating output.

Indoor Air Purification System Installation: Arrived on-site to address indoor air quality concerns including excessive dust and allergy symptoms. Installed a whole-home air purification system within the air handler, sealed duct connections, verified proper airflow, and tested system operation to improve overall air cleanliness and comfort.

Heat Pump Installation: Dispatched to replace an aging heat pump that was no longer meeting heating and cooling demands. Removed the existing unit, installed a new high-efficiency heat pump, connected refrigerant lines and electrical wiring, evacuated and charged the system, programmed controls, and tested both heating and cooling modes for proper performance.

Heating System Repair: Arrived on-site to diagnose a furnace short cycling and failing to maintain set temperature. Inspected flame sensor, pressure switch, and airflow conditions. Found heavy oxidation on the flame sensor causing intermittent flame loss. Cleaned the sensor, verified stable burner operation, and tested multiple heating cycles to confirm consistent operation.

AC Repair: Dispatched to address an air conditioning system blowing warm air during operation. Inspected the outdoor condenser, indoor evaporator coil, and electrical components. Identified a weak capacitor and low refrigerant charge. Replaced the capacitor, corrected refrigerant levels, and tested system pressures, airflow, and temperature split to confirm restored cooling performance.

Heat Pump Repair: Arrived on-site to troubleshoot a heat pump that was operating but not delivering warm air. Inspected thermostat settings, electrical components, and refrigerant controls. Diagnosed a failed reversing valve solenoid preventing the system from shifting into heating mode. Replaced the solenoid, verified valve operation, and tested heating performance under load.

Furnace Replacement: Dispatched to evaluate a furnace producing abnormal readings during inspection. Performed a full heat exchanger evaluation and confirmed a crack causing unsafe carbon monoxide levels. Shut down the system, removed the existing furnace, and installed a new high-efficiency furnace. Connected ductwork, gas, electrical, and venting systems, calibrated controls, and tested startup, airflow, and heat output to ensure safe operation.

Heating System Repair: Arrived on-site to diagnose a furnace that was not producing heat. Verified thermostat operation and confirmed a call for heat. Inspected the ignition sequence and safety controls, identifying a failed hot surface igniter preventing burner ignition. Replaced the igniter, confirmed proper flame establishment, monitored the heating cycle, and verified safe and consistent heat output.

installed 3 furnace w/ drain pan + float switch. + recipe water heater

HVAC Repair: The homeowner reported the furnace would ignite briefly and then shut down. After diagnosing the issue, I found a corroded flame sensor failing to detect proper ignition. I cleaned and reinstalled the sensor, then tested the ignition sequence. The heating system now runs reliably and maintains steady operation throughout the home.

Indoor Air Purification System Install: The homeowner wanted to improve air quality due to allergies. After evaluating their HVAC system, I installed a whole-home air purification unit integrated into the existing ductwork. I verified airflow, checked electrical connections, and confirmed proper operation. The home now benefits from cleaner, healthier indoor air.

AC Repair: The client reported that their AC system was shortcycling. After diagnosing the unit, I found a failing thermostat relay that was causing the system to start and stop rapidly. I replaced the defective relay, secured all low-voltage wiring, and tested the system thoroughly. The AC now operates with stable, efficient cooling cycles.

Furnace Maintenance: During a routine maintenance visit, I inspected and cleaned the burner assembly, checked safety controls, and tested electrical connections. I also replaced a dirty filter and calibrated the thermostat for accurate operation. The furnace now runs smoothly and efficiently, ready for dependable seasonal performance.

Furnace Replacement: A homeowner reported repeated heating failures and unusually long heat-up times. After inspecting the system, I found severe heat exchanger deterioration and multiple failing safety components, making repair unsafe and impractical. I recommended a complete furnace replacement and helped the homeowner select a high-efficiency model suitable for their home. Once installed and tested, the new furnace provided reliable, safe, and energy-efficient heating.

Heating Repairs: A homeowner reported that their heating system was cycling on and off frequently and not maintaining a consistent temperature. Upon inspection, we found a clogged condensate line and a failing gas valve that were preventing proper operation. Replaced the faulty gas valve, cleared the condensate line, and tested the system. The heating system now runs smoothly, providing consistent and efficient warmth throughout the home.

Whole-Home Humidifier Installation: The homeowner requested a solution to improve indoor air quality and comfort during the dry months. Installed a whole-home humidifier in the HVAC system, connecting it to the ductwork and water supply for optimal operation. Tested the system to ensure proper humidity levels and safe operation. The humidifier now helps maintain balanced indoor moisture, reducing dryness, improving comfort, and protecting wood surfaces and furnishings throughout the home.

Full HVAC System Replacement: The homeowner’s existing HVAC system was aging and inefficient, leading to inconsistent heating and cooling. Removed the old system and installed a new high-efficiency furnace and air conditioner along with a modern thermostat. Verified proper duct connections, airflow, and refrigerant charge, and tested the system through multiple heating and cooling cycles. The new system now provides reliable, energy-efficient comfort throughout the home year-round.

Furnace Repairs: A homeowner reported that their furnace would not ignite. Upon inspection, we discovered a malfunctioning gas valve that was preventing gas flow to the burners. Replaced the faulty valve, tested the ignition sequence, and verified proper flame characteristics. The furnace now operates reliably, providing safe and consistent heat throughout the home.

installed Amana furnace w/ drain pan w/ float switch 16x25x1 filter rack

I installed a water system with an expansion tank and a ball valve.

Replaced faulty run capacitor on a Rheem Classic condenser. Verified microfarads matched manufacturer rating and confirmed compressor started smoothly on restart.