Air Conditioning System Repair: The homeowner reported the AC system was turning on and off frequently without fully cooling the home. Upon inspection, we identified a clogged condensate line triggering safety shutoffs and a weak compressor capacitor affecting system performance. Cleared the blockage, replaced the capacitor, and inspected the drain system for proper flow. After testing, the AC now runs consistently and delivers strong, reliable cooling throughout the home.

Preventative AC Maintenance: Completed a scheduled maintenance visit to prepare the system for heavy summer usage. Cleaned condenser coils to improve heat transfer, checked refrigerant levels, inspected electrical components, and replaced the air filter. Also tested capacitor strength and verified proper airflow across the evaporator coil. After a full system test, confirmed the unit is operating at peak efficiency and ready for continued reliable performance.

AC System & Indoor Air Quality Installation: The homeowner requested improved cooling performance along with better indoor air quality. Installed a new high-efficiency air conditioning system paired with an upgraded filtration system within the ductwork. Ensured proper system integration with the existing air handler, sealed connections, and tested airflow. After installation, we verified system performance and cooling output. The home now benefits from cleaner air and more consistent, efficient cooling.

Air Conditioner Repair: A homeowner reported their AC system would not power on at all despite thermostat adjustments. During inspection, we found a failed control board that was preventing communication between system components. Replaced the control board, tightened and inspected wiring connections, and verified proper low-voltage operation. Tested full system startup and shutdown cycles. The AC now powers on reliably and provides consistent cooling.

AC Maintenance & Repair: The homeowner reported inconsistent indoor temperatures and reduced cooling performance during peak heat hours. Inspection revealed a malfunctioning return air temperature sensor and slightly low refrigerant levels due to minor leakage. Repaired the sensor issue, performed a leak check, and recharged the system to proper levels. Tested system performance across multiple cycles. The AC now maintains steady indoor temperatures and operates more efficiently.

AC System Replacement: The homeowner reported loud operation, longer run times, and uneven cooling throughout the house. Inspection revealed a failing compressor along with multiple worn components, making repair no longer cost-effective. We removed the existing system and installed a new high-efficiency air conditioning unit, including a properly matched indoor coil. Charged the system to manufacturer specifications, verified airflow, and tested temperature split. The new system now cools evenly, operates quietly, and runs much more efficiently.

AC Repair Service: The homeowner reported that their air conditioning system would not start during the hottest part of the day. After performing a full diagnostic, we identified a failed dual-run capacitor and a worn contactor that were preventing the compressor and condenser fan from engaging. Replaced both components, inspected all electrical connections for signs of wear, and verified proper voltage. Cycled the system multiple times to confirm reliable startup and consistent cooling throughout the home.

installed full systems with float switch and in line switch

installed trane full systems w/drain pan w/float switch � in line switch

Air Purification Installation: Dispatched to resolve persistent odors and concerns about indoor air quality and airborne contaminants. Installed a UV light air purification system within the HVAC unit, mounted the lamp assembly securely, connected electrical power with safety shutoff, and tested operation to reduce bacteria, mold, and odors throughout the home.

Heat Pump Repair: Arrived on-site to inspect a heat pump experiencing ice buildup on the outdoor unit during cold conditions. Tested defrost controls and sensors, identifying a malfunctioning defrost control board. Replaced the board, verified proper defrost timing, and tested system operation to ensure reliable winter performance.

Heating System Repair: Dispatched to address uneven temperatures throughout the home. Inspected blower motor performance, ductwork, and airflow restrictions. Diagnosed a failing blower motor and debris buildup on the blower wheel. Replaced the motor, cleaned the wheel, and tested airflow and temperature distribution to restore even heating.

AC Repair: Arrived on-site to troubleshoot an air conditioning system that would not start. Verified incoming power, inspected electrical components, and identified a failed contactor and loose wiring connections. Replaced the contactor, secured all electrical connections, and tested system startup and cooling operation.

Furnace Replacement: Dispatched to evaluate a furnace experiencing repeated fault codes and safety shutdowns. Inspection revealed a failed secondary heat exchanger creating unsafe operating conditions. Removed the furnace, installed a new high-efficiency replacement, ensured proper venting and condensate drainage, and tested system startup and heating output.

Indoor Air Purification System Installation: Arrived on-site to address indoor air quality concerns including excessive dust and allergy symptoms. Installed a whole-home air purification system within the air handler, sealed duct connections, verified proper airflow, and tested system operation to improve overall air cleanliness and comfort.

Heat Pump Installation: Dispatched to replace an aging heat pump that was no longer meeting heating and cooling demands. Removed the existing unit, installed a new high-efficiency heat pump, connected refrigerant lines and electrical wiring, evacuated and charged the system, programmed controls, and tested both heating and cooling modes for proper performance.

Heating System Repair: Arrived on-site to diagnose a furnace short cycling and failing to maintain set temperature. Inspected flame sensor, pressure switch, and airflow conditions. Found heavy oxidation on the flame sensor causing intermittent flame loss. Cleaned the sensor, verified stable burner operation, and tested multiple heating cycles to confirm consistent operation.

AC Repair: Dispatched to address an air conditioning system blowing warm air during operation. Inspected the outdoor condenser, indoor evaporator coil, and electrical components. Identified a weak capacitor and low refrigerant charge. Replaced the capacitor, corrected refrigerant levels, and tested system pressures, airflow, and temperature split to confirm restored cooling performance.

Heat Pump Repair: Arrived on-site to troubleshoot a heat pump that was operating but not delivering warm air. Inspected thermostat settings, electrical components, and refrigerant controls. Diagnosed a failed reversing valve solenoid preventing the system from shifting into heating mode. Replaced the solenoid, verified valve operation, and tested heating performance under load.

Furnace Replacement: Dispatched to evaluate a furnace producing abnormal readings during inspection. Performed a full heat exchanger evaluation and confirmed a crack causing unsafe carbon monoxide levels. Shut down the system, removed the existing furnace, and installed a new high-efficiency furnace. Connected ductwork, gas, electrical, and venting systems, calibrated controls, and tested startup, airflow, and heat output to ensure safe operation.

Heating System Repair: Arrived on-site to diagnose a furnace that was not producing heat. Verified thermostat operation and confirmed a call for heat. Inspected the ignition sequence and safety controls, identifying a failed hot surface igniter preventing burner ignition. Replaced the igniter, confirmed proper flame establishment, monitored the heating cycle, and verified safe and consistent heat output.

installed 3 furnace w/ drain pan + float switch. + recipe water heater

HVAC Repair: The homeowner reported the furnace would ignite briefly and then shut down. After diagnosing the issue, I found a corroded flame sensor failing to detect proper ignition. I cleaned and reinstalled the sensor, then tested the ignition sequence. The heating system now runs reliably and maintains steady operation throughout the home.

Indoor Air Purification System Install: The homeowner wanted to improve air quality due to allergies. After evaluating their HVAC system, I installed a whole-home air purification unit integrated into the existing ductwork. I verified airflow, checked electrical connections, and confirmed proper operation. The home now benefits from cleaner, healthier indoor air.

AC Repair: The client reported that their AC system was shortcycling. After diagnosing the unit, I found a failing thermostat relay that was causing the system to start and stop rapidly. I replaced the defective relay, secured all low-voltage wiring, and tested the system thoroughly. The AC now operates with stable, efficient cooling cycles.